top of page

Model Predictive Controller Design for Buck Converter in MATLAB

9 minutes ago
6 min read

Model Predictive Controller Design for Buck Converter in MATLAB


𝐈𝐧𝐭𝐫𝐨𝐝𝐮𝐜𝐭𝐢𝐨𝐧

The Model Predictive Controller (MPC) Design for Buck Converter in MATLAB demonstrates an advanced voltage regulation technique using MATLAB and Simulink. The system employs Model Predictive Control to regulate the output voltage of a DC-DC buck converter by adjusting the duty cycle of its switching device.


Model Predictive Controller Design for Buck Converter

Model Predictive Controller Design for Buck Converter in MATLAB
₹8,000.00₹4,000.00
Buy Now


Unlike conventional control methods, MPC predicts future system behavior using a mathematical model and determines suitable control actions to achieve the desired output voltage.

  • Designed and simulated using MATLAB/Simulink.

  • Implements MPC-based output voltage regulation.

  • Uses a system identification approach to estimate the converter transfer function.

  • Controls the converter through duty cycle adjustment.

  • Demonstrates voltage reference tracking under changing operating conditions.

𝐒𝐲𝐬𝐭𝐞𝐦 𝐎𝐯𝐞𝐫𝐯𝐢𝐞𝐰

The proposed system consists of a DC-DC buck converter integrated with a Model Predictive Controller. The buck converter steps down the input DC voltage to a regulated lower output voltage.

The controller continuously monitors the output voltage and determines the switching duty cycle required to track the reference voltage.

Main Components

Component

Function

DC Voltage Source

Supplies input power to the converter

IGBT Switch

Controls energy transfer through PWM switching

Diode

Provides the freewheeling current path

Inductor

Stores energy and smooths current

Capacitor

Reduces output voltage ripple

Resistive Load

Represents the connected electrical load

PWM Generator

Converts the duty cycle into switching pulses

MPC Controller

Regulates the converter output voltage

Voltage Measurement

Provides output voltage feedback

System Specifications

The simulation demonstrates the following operating conditions.

Parameter

Value

Converter Type

DC-DC Buck Converter

Input Voltage

70 V

Initial Reference Voltage

50 V

Final Reference Voltage

40 V

Reference Change Time

0.5 s

Simulation Duration

1 s

Control Technique

Model Predictive Control

Controlled Variable

Output Voltage

Manipulated Variable

PWM Duty Cycle

Disturbance Input

0

Simulation Platform

MATLAB/Simulink

The inductor, capacitor, load resistance, and switching frequency are determined during the converter design stage.

𝐁𝐮𝐜𝐤 𝐂𝐨𝐧𝐯𝐞𝐫𝐭𝐞𝐫 𝐃𝐞𝐬𝐢𝐠𝐧

The first stage involves designing the buck converter based on the required electrical specifications.

Design Input Parameters

  • Rated Power: Determines converter power-handling requirements.

  • Input Voltage: Defines the DC supply voltage.

  • Output Voltage: Specifies the required regulated voltage.

  • Switching Frequency: Determines the switching operation of the converter.

  • Inductor Current Ripple: Used to select a suitable inductance.

  • Output Voltage Ripple: Used to select the output filter capacitor.

  • Load Resistance: Determines the output loading condition.

  • Duty Cycle: Controls the relationship between input and output voltage.

A MATLAB design program calculates the required inductor, capacitor, resistance, and nominal duty cycle.

These calculated parameters are then used to construct the buck converter circuit in Simulink.

𝐖𝐨𝐫𝐤𝐢𝐧𝐠 𝐏𝐫𝐨𝐜𝐞𝐬𝐬

The complete implementation includes converter modeling, data acquisition, transfer function estimation, MPC design, and closed-loop simulation.

Buck Converter Design

Inductor, capacitor, load resistance, duty cycle

MATLAB/Simulink Circuit

DC source, IGBT, diode, LC filter, load

Input–Output Data Acquisition

Duty cycle input and output voltage

System Identification

Estimate the converter transfer function

MPC Controller Design

Prediction model and controller configuration

Closed-Loop Voltage Regulation

50 V to 40 V reference tracking

Step 1: Develop the Simulink Model

The converter model is constructed using the electrical components available in MATLAB/Simulink.

  • Connect the DC source to the switching circuit.

  • Place the IGBT and freewheeling diode.

  • Connect the inductor and output capacitor.

  • Add the resistive load.

  • Measure the output voltage.

  • Connect a PWM generator to control the IGBT.

Step 2: Collect Input and Output Data

Input-output data are collected to develop a mathematical representation of the buck converter.

Signal

Description

Input Data

Converter duty cycle

Output Data

Measured output voltage

Data Storage

MATLAB Workspace

Identification Method

Time-domain system identification

The converter is initially simulated using the nominal duty cycle calculated during the design process.

Step 3: Estimate the Transfer Function

The System Identification Toolbox is used to estimate the converter transfer function.

  • Open the System Identification application in MATLAB.

  • Import the collected input and output data.

  • Specify the starting time and sample time.

  • Select transfer function estimation.

  • Estimate the system model.

  • Export the identified transfer function to the MATLAB workspace.

The estimated model represents the relationship between the converter duty cycle and output voltage.

The accuracy of this identified model is important for MPC performance.

𝐂𝐨𝐧𝐭𝐫𝐨𝐥 𝐒𝐭𝐫𝐚𝐭𝐞𝐠𝐲

The Model Predictive Controller determines the duty cycle required to maintain the desired output voltage.

MPC Controller Configuration

The controller is designed using the MPC Designer available in MATLAB.

Controller Parameter

Configuration

Controller Type

Model Predictive Controller

Plant Model

Identified Buck Converter Model

Manipulated Variable

Duty Cycle

Measured Output

Buck Converter Output Voltage

Reference Input

Desired Output Voltage

Measured Disturbance

Zero in the demonstrated setup

Controller Sample Time

Configured during MPC design

Control Objective

Output Voltage Reference Tracking

Controller Design Procedure

  1. Insert the MPC Controller block in Simulink.

  2. Configure the identified converter model.

  3. Connect the plant output as feedback.

  4. Set the required output voltage reference.

  5. Configure the controller sample time.

  6. Open the MPC Designer.

  7. Analyze the predicted plant response.

  8. Update the MPC Controller block with the designed controller.

The controller uses the prediction model to determine suitable control actions over a prediction horizon.

Controller output: Duty cycle command supplied to the PWM generator.

Feedback signal: Actual buck converter output voltage.

The duty cycle should be constrained within the permissible operating range of the converter.

𝐒𝐢𝐦𝐮𝐥𝐚𝐭𝐢𝐨𝐧 𝐑𝐞𝐬𝐮𝐥𝐭𝐬

The proposed MPC-controlled buck converter is evaluated under constant and changing reference voltage conditions.

Test 1: Constant Reference Voltage

The initial simulation is performed with a 50 V reference voltage.

Parameter

Value

Input Voltage

70 V

Reference Voltage

50 V

Output Voltage

Approximately 50 V

Reference Condition

Constant

Observation: The output voltage follows the desired 50 V reference, demonstrating voltage regulation under the simulated operating conditions.

Test 2: Reference Voltage Variation

A step change is introduced to evaluate the dynamic response of the MPC controller.

Parameter

Value

Input Voltage

70 V

Initial Reference

50 V

Final Reference

40 V

Step Change Time

0.5 s

Final Output Voltage

Approximately 40 V

Simulation Duration

1 s

Output Voltage Reference Tracking

Illustrative reference-tracking profile based on the reported simulation; not exported simulation samples.

■ Reference voltage

■ Illustrative output

The graph illustrates the expected tracking behavior, not a measured transient waveform from the original model. Exact settling time and overshoot are not specified in the transcript.

Results Discussion

  • The output voltage initially remains near 50 V.

  • At 0.5 seconds, the voltage reference decreases to 40 V.

  • The MPC controller adjusts the duty cycle based on the reference change.

  • The converter output follows the new reference and reaches approximately 40 V.

  • The simulation demonstrates closed-loop reference tracking using MPC.

These results show that the controller can regulate the buck converter output voltage under the demonstrated reference changes.

𝐊𝐞𝐲 𝐅𝐞𝐚𝐭𝐮𝐫𝐞𝐬

  • MPC-Based Regulation: Uses model predictions for output voltage control.

  • Automated Converter Design: MATLAB calculations support selection of circuit parameters.

  • System Identification: Estimates the converter model from input-output data.

  • Closed-Loop Control: Uses continuous output voltage feedback.

  • Dynamic Reference Tracking: Demonstrates response to changes in the desired voltage.

  • PWM Integration: Controls IGBT switching through duty cycle commands.

  • MATLAB MPC Designer: Supports controller configuration, analysis, and tuning.

  • Simulation-Based Verification: Enables visualization of converter voltage, current, and power behavior.

𝐀𝐩𝐩𝐥𝐢𝐜𝐚𝐭𝐢𝐨𝐧𝐬

The MPC-controlled buck converter approach is relevant to several power electronics applications.

  • DC-DC Power Supplies: Regulated voltage conversion for electronic systems.

  • Battery Charging Systems: Controlled DC voltage conversion for charging interfaces.

  • Renewable Energy Systems: DC voltage regulation in solar PV and energy storage systems.

  • Electric Vehicles: Auxiliary DC-DC voltage conversion.

  • DC Microgrids: Voltage regulation in DC distribution architectures.

  • Industrial Power Electronics: Advanced converter control development.

  • Research and Education: Study of predictive control, converter modeling, and system identification.

𝐖𝐡𝐲 𝐔𝐬𝐞 𝐌𝐏𝐂 𝐟𝐨𝐫 𝐚 𝐁𝐮𝐜𝐤 𝐂𝐨𝐧𝐯𝐞𝐫𝐭𝐞𝐫?

Model Predictive Control provides a systematic approach to controlling power electronic converters.

Feature

MPC-Based Approach

Control Principle

Model-based prediction and optimization

Voltage Regulation

Feedback-based voltage tracking

Reference Changes

Recalculates control action as the reference changes

Constraints

Can incorporate duty cycle and other operating limits

Mathematical Model

Requires a sufficiently accurate converter model

Implementation

MATLAB/Simulink with MPC Toolbox

Tuning

Prediction horizon, control horizon, and controller weights

MPC can offer flexible control and constraint handling, although its actual performance depends on model accuracy, controller tuning, sampling time, and computational requirements.

𝐂𝐨𝐧𝐜𝐥𝐮𝐬𝐢𝐨𝐧

The Model Predictive Controller Design for Buck Converter in MATLAB demonstrates the complete procedure for implementing model-based voltage regulation in a DC-DC converter.

The simulation combines buck converter parameter calculation, MATLAB/Simulink circuit development, system identification, transfer function estimation, and MPC controller design.

The demonstrated controller successfully tracks a reference voltage change from 50 V to 40 V at 0.5 seconds, showing its ability to adjust converter operation according to the desired output voltage.

This implementation provides a useful learning and research platform for understanding Model Predictive Control in modern power electronics systems.

Explore more MATLAB/Simulink learning models and tutorials at LMS Solution.


Comments


bottom of page