Fuzzy MPPT Solar PV Charger Controller For Battery System
Fuzzy MPPT Solar PV Charger Controller For Battery System
The Fuzzy MPPT Solar PV Charger Controller for Battery System in MATLAB/Simulink is designed to extract maximum power from a solar photovoltaic (PV) array and efficiently charge a battery using a DC-DC Zeta converter.
This system combines 𝐅𝐮𝐳𝐳𝐲 𝐋𝐨𝐠𝐢𝐜-𝐁𝐚𝐬𝐞𝐝 𝐌𝐚𝐱𝐢𝐦𝐮𝐦 𝐏𝐨𝐰𝐞𝐫 𝐏𝐨𝐢𝐧𝐭 𝐓𝐫𝐚𝐜𝐤𝐢𝐧𝐠 (𝐌𝐏𝐏𝐓) with a battery charging controller to improve solar energy utilization under varying irradiation conditions.
𝐈𝐧𝐭𝐫𝐨𝐝𝐮𝐜𝐭𝐢𝐨𝐧
Solar photovoltaic systems generate electrical power depending on solar irradiation and temperature. Therefore, an efficient MPPT controller is necessary to extract maximum available power from the PV array.

This MATLAB/Simulink model integrates:
𝐒𝐨𝐥𝐚𝐫 𝐏𝐕 𝐀𝐫𝐫𝐚𝐲: Generates renewable electrical energy.
𝐅𝐮𝐳𝐳𝐲 𝐋𝐨𝐠𝐢𝐜 𝐌𝐏𝐏𝐓: Tracks the maximum power operating point.
𝐃𝐂-𝐃𝐂 𝐙𝐞𝐭𝐚 𝐂𝐨𝐧𝐯𝐞𝐫𝐭𝐞𝐫: Adjusts the PV voltage for battery charging.
𝐁𝐚𝐭𝐭𝐞𝐫𝐲 𝐂𝐡𝐚𝐫𝐠𝐢𝐧𝐠 𝐂𝐨𝐧𝐭𝐫𝐨𝐥𝐥𝐞𝐫: Controls the charging operation using battery voltage and state of charge.
𝐁𝐚𝐭𝐭𝐞𝐫𝐲 𝐄𝐧𝐞𝐫𝐠𝐲 𝐒𝐭𝐨𝐫𝐚𝐠𝐞: Stores the extracted solar energy.
The proposed control arrangement maintains effective battery charging while responding to changes in available solar power.
𝐒𝐲𝐬𝐭𝐞𝐦 𝐎𝐯𝐞𝐫𝐯𝐢𝐞𝐰
The solar PV array is connected to a 48 V battery through a Zeta DC-DC converter. The converter receives PWM switching pulses from the integrated fuzzy MPPT and battery charging controller.
Solar PV Array Specifications
Parameter | Specification |
PV module rated power | 250 W |
Series-connected modules | 4 |
Parallel strings | 2 |
Total PV array rated power | 2000 W |
Open-circuit voltage (Voc) | 36.6 V per module |
Maximum power voltage (Vmpp) | 30.9 V per module |
Short-circuit current (Isc) | 8.75 A per module |
Maximum power current (Impp) | 8.1 A per module |
Standard irradiation | 1000 W/m² |
Standard temperature | 25°C |
PV operating voltage near MPP | Approximately 123 V |
Battery Specifications
Parameter | Specification |
Battery nominal voltage | 48 V |
Rated capacity | 200 Ah |
Initial state of charge | 30% |
Full-charge voltage mentioned | 52.26 V |
Charging cutoff voltage used in controller | 55.4 V |
Maximum SOC charging condition | Below 100% |
Charging strategy | Voltage and SOC-based charging permission |
The 55.4 V cutoff is the value implemented in the described simulation and should be validated against the actual battery chemistry and manufacturer's recommended charging limits.
𝐖𝐨𝐫𝐤𝐢𝐧𝐠 𝐏𝐫𝐨𝐜𝐞𝐬𝐬
The system operates through the following sequence:
Solar Power Generation: The 2000 W PV array generates power according to solar irradiation and temperature.
PV Measurement: The controller measures the instantaneous PV voltage and current.
Maximum Power Tracking: The fuzzy logic MPPT algorithm analyzes the PV power-voltage slope.
Duty Cycle Generation: The fuzzy controller determines the converter duty cycle.
Voltage Conversion: The Zeta converter reduces the PV voltage to a suitable battery charging level.
Battery Charging Verification: The charging controller checks battery voltage and SOC.
PWM Switching: Charging pulses are enabled only when the specified charging conditions are satisfied.
𝐅𝐮𝐳𝐳𝐲 𝐋𝐨𝐠𝐢𝐜 𝐌𝐏𝐏𝐓 𝐂𝐨𝐧𝐭𝐫𝐨𝐥 𝐒𝐭𝐫𝐚𝐭𝐞𝐠𝐲
The fuzzy MPPT controller determines the converter duty cycle based on changes in PV power with respect to PV voltage.
Fuzzy Controller Configuration
Parameter | Description |
Controller type | Fuzzy Logic Controller |
Number of inputs | 1 |
Input variable | PV power-voltage slope (dP/dV) |
Number of outputs | 1 |
Output variable | Converter duty cycle |
Input range | −0.1 to +0.1 |
Duty cycle range | 0.15 to 0.40 |
Input membership functions | 7 triangular functions |
Output membership functions | 7 |
Number of fuzzy rules | 7 |
Fuzzy Logic Rule Base
The controller uses seven membership categories with an inverse relationship between the PV power-voltage slope and duty-cycle control category.
PV Slope Category | Duty-Cycle Category |
Negative Big (NB) | Positive Big (PB) |
Negative Medium (NM) | Positive Medium (PM) |
Negative Small (NS) | Positive Small (PS) |
Zero (ZE) | Zero (ZE) |
Positive Small (PS) | Negative Small (NS) |
Positive Medium (PM) | Negative Medium (NM) |
Positive Big (PB) | Negative Big (NB) |
𝐌𝐚𝐢𝐧 𝐀𝐝𝐯𝐚𝐧𝐭𝐚𝐠𝐞: The fuzzy controller uses a compact seven-rule structure to adjust the converter duty cycle in response to changing PV operating conditions.
𝐃𝐂-𝐃𝐂 𝐙𝐞𝐭𝐚 𝐂𝐨𝐧𝐯𝐞𝐫𝐭𝐞𝐫
The Zeta converter acts as the power-conditioning interface between the PV array and the battery.
Converter Operating Details
Parameter | Description |
Converter topology | DC-DC Zeta converter |
Operating capability | Buck and boost |
Operating mode in this model | Buck mode |
PV input voltage | Approximately 120–123 V |
Battery nominal voltage | 48 V |
Control method | PWM |
Duty cycle command | Fuzzy MPPT with charging enable logic |
The converter operates in buck mode because the PV voltage is higher than the required battery charging voltage.
𝐊𝐞𝐲 𝐁𝐞𝐧𝐞𝐟𝐢𝐭: The Zeta converter provides voltage conversion while the MPPT controller adjusts its switching operation to extract the available solar power.
𝐁𝐚𝐭𝐭𝐞𝐫𝐲 𝐂𝐡𝐚𝐫𝐠𝐢𝐧𝐠 𝐂𝐨𝐧𝐭𝐫𝐨𝐥
The battery charging controller is integrated with the fuzzy MPPT system to prevent charging beyond the defined voltage and SOC limits.
Battery Charging Conditions
Battery Condition | Controller Action |
Battery voltage ≤ 55.4 V | Charging permitted by voltage condition |
Battery voltage > 55.4 V | Charging disabled |
Battery SOC < 100% | Charging permitted by SOC condition |
Battery SOC ≥ 100% | Charging disabled |
Both charging conditions satisfied | PWM enabled |
Either charging condition not satisfied | PWM disabled |
This arrangement uses two operating checks:
𝐕𝐨𝐥𝐭𝐚𝐠𝐞 𝐋𝐢𝐦𝐢𝐭: Charging is stopped when the battery voltage exceeds the selected threshold.
𝐒𝐎𝐂 𝐋𝐢𝐦𝐢𝐭: Charging is disabled when the battery reaches the maximum SOC limit.
The described controller is a voltage/SOC-based charging enable system rather than a complete constant-current/constant-voltage charging algorithm.
𝐒𝐢𝐦𝐮𝐥𝐚𝐭𝐢𝐨𝐧 𝐑𝐞𝐬𝐮𝐥𝐭𝐬
The MATLAB/Simulink model is evaluated under changing solar irradiation conditions to examine MPPT tracking and battery charging performance.
Simulation Conditions
Parameter | Value |
Initial solar irradiation | 1000 W/m² |
Reduced solar irradiation | 500 W/m² |
Irradiation change time | Approximately 4.1 s |
PV rated power | 2000 W |
Battery voltage rating | 48 V |
Initial battery SOC | 30% |
PV Power Tracking Performance
Parameter | 1000 W/m² | 500 W/m² |
PV voltage | Approximately 123 V | Approximately 123.4 V |
PV current | Approximately 16–17 A | 7.955 A |
Theoretical maximum PV power | Approximately 2000 W | Approximately 983.9 W |
Tracked PV power | Approximately 1990–2000 W | 981.2 W |
Battery Charging Results
Parameter | Higher Irradiation | Lower Irradiation |
Solar irradiation | 1000 W/m² | 500 W/m² |
PV output power | Approximately 2000 W | 981.2 W |
Battery voltage | Approximately 48 V | Approximately 48 V |
Battery charging current | Approximately −41 A | Approximately −20 A |
Battery operating condition | Charging | Charging at reduced current |
Performance Observations
𝐏𝐕 𝐏𝐨𝐰𝐞𝐫 𝐓𝐫𝐚𝐜𝐤𝐢𝐧𝐠: The controller tracks approximately 981.2 W against an available maximum of around 983.9 W at 500 W/m².
𝐈𝐫𝐫𝐚𝐝𝐢𝐚𝐭𝐢𝐨𝐧 𝐑𝐞𝐬𝐩𝐨𝐧𝐬𝐞: The controller responds to the sudden reduction in solar irradiation at approximately 4.1 seconds.
𝐓𝐫𝐚𝐧𝐬𝐢𝐞𝐧𝐭 𝐁𝐞𝐡𝐚𝐯𝐢𝐨𝐫: PV voltage, current, and power experience short-term disturbances before settling.
𝐁𝐚𝐭𝐭𝐞𝐫𝐲 𝐂𝐡𝐚𝐫𝐠𝐢𝐧𝐠: The charging current reduces from approximately −41 A to −20 A as PV power decreases.
𝐁𝐚𝐭𝐭𝐞𝐫𝐲 𝐒𝐎𝐂: The battery state of charge gradually increases during charging.
The negative battery current indicates charging according to the measurement sign convention used in the simulation.
Reported Efficiency
98.63%
Reported PV-to-battery charging efficiency
This value is reported in the simulation explanation based on battery charging power relative to PV power. It should be distinguished from MPPT tracking efficiency and independently verified for the selected operating interval.
𝐊𝐞𝐲 𝐅𝐞𝐚𝐭𝐮𝐫𝐞𝐬
𝐅𝐮𝐳𝐳𝐲 𝐋𝐨𝐠𝐢𝐜 𝐌𝐏𝐏𝐓: Tracks maximum solar power using a seven-rule fuzzy controller.
𝐙𝐞𝐭𝐚 𝐂𝐨𝐧𝐯𝐞𝐫𝐭𝐞𝐫: Supports buck and boost voltage conversion.
𝐁𝐚𝐭𝐭𝐞𝐫𝐲 𝐂𝐡𝐚𝐫𝐠𝐢𝐧𝐠 𝐂𝐨𝐧𝐭𝐫𝐨𝐥: Uses battery voltage and SOC-based conditions.
𝐃𝐲𝐧𝐚𝐦𝐢𝐜 𝐈𝐫𝐫𝐚𝐝𝐢𝐚𝐭𝐢𝐨𝐧 𝐓𝐞𝐬𝐭𝐢𝐧𝐠: Evaluates controller behavior at 1000 W/m² and 500 W/m².
𝐒𝐢𝐦𝐮𝐥𝐢𝐧𝐤 𝐈𝐦𝐩𝐥𝐞𝐦𝐞𝐧𝐭𝐚𝐭𝐢𝐨𝐧: Integrates PV modeling, converter switching, MPPT, and battery measurement.
𝐏𝐞𝐫𝐟𝐨𝐫𝐦𝐚𝐧𝐜𝐞 𝐌𝐨𝐧𝐢𝐭𝐨𝐫𝐢𝐧𝐠: Observes PV voltage, current, power, battery current, voltage, and SOC.
𝐀𝐩𝐩𝐥𝐢𝐜𝐚𝐭𝐢𝐨𝐧𝐬
The Fuzzy MPPT Solar PV Battery Charger Controller can be studied and adapted for several renewable energy applications:
Solar-powered battery charging systems
Standalone solar photovoltaic energy systems
Solar-powered DC microgrids
Renewable energy storage applications
Intelligent MPPT algorithm research
DC-DC converter control studies
Battery charging control development
MATLAB/Simulink renewable energy education
𝐂𝐨𝐧𝐜𝐥𝐮𝐬𝐢𝐨𝐧
The Fuzzy MPPT Solar PV Charger Controller for Battery System demonstrates the integration of fuzzy logic maximum power point tracking, a DC-DC Zeta converter, and battery charging control in MATLAB/Simulink.
The simulation shows that:
The 2000 W PV array supplies power according to solar irradiation.
The fuzzy MPPT controller tracks the available maximum PV power.
The Zeta converter operates in buck mode for charging the 48 V battery.
The battery charging controller uses voltage and SOC-based conditions.
The charging current automatically decreases when solar irradiation is reduced.
The reported PV-to-battery charging efficiency is approximately 98.63%.
This simulation provides a useful platform for students, researchers, and engineers studying 𝐅𝐮𝐳𝐳𝐲 𝐌𝐏𝐏𝐓, 𝐒𝐨𝐥𝐚𝐫 𝐏𝐕 𝐂𝐡𝐚𝐫𝐠𝐢𝐧𝐠, 𝐙𝐞𝐭𝐚 𝐂𝐨𝐧𝐯𝐞𝐫𝐭𝐞𝐫 𝐂𝐨𝐧𝐭𝐫𝐨𝐥, and 𝐁𝐚𝐭𝐭𝐞𝐫𝐲 𝐄𝐧𝐞𝐫𝐠𝐲 𝐒𝐭𝐨𝐫𝐚𝐠𝐞 in MATLAB/Simulink.
For more MATLAB/Simulink renewable energy simulation models and technical tutorials, visit www.lmssolution.net.in.



Comments