top of page

Fuzzy MPPT For Solar PV Battery DC Microgrid System in MATLAB

1 day ago
9 min read

Fuzzy MPPT For Solar PV Battery DC Microgrid System in MATLAB


𝐈𝐧𝐭𝐫𝐨𝐝𝐮𝐜𝐭𝐢𝐨𝐧

The Fuzzy MPPT For Solar PV Battery DC Microgrid System in MATLAB demonstrates a complete solar photovoltaic–battery DC microgrid developed in MATLAB/Simulink.


Fuzzy MPPT For Solar PV Battery DC Microgrid System

Fuzzy MPPT For Solar PV Battery DC Microgrid System in MATLAB
₹10,000.00₹5,000.00
Buy Now


The system combines:

  • Solar PV generation

  • Fuzzy Logic based MPPT control

  • DC–DC boost converter

  • Battery energy storage

  • Bidirectional DC–DC converter

  • DC load

  • DC bus voltage control

  • Automatic battery charging and discharging

  • Variable solar irradiation testing

The main objective is to extract the maximum available power from the PV array while maintaining the DC bus voltage close to 400 V under changing solar irradiation.

The battery automatically absorbs excess PV energy or supplies the power deficit depending on the balance between PV generation and load demand.

𝐒𝐲𝐬𝐭𝐞𝐦 𝐎𝐯𝐞𝐫𝐯𝐢𝐞𝐰

The simulated DC microgrid contains two major energy sources:

  1. Solar PV array

  2. Battery energy storage system

The PV system is connected to the common DC bus through a boost converter.

The battery is connected through a bidirectional DC–DC converter, allowing energy flow in both directions.

The overall structure can be understood as:

Solar PV → Boost Converter → DC Bus → DC Load

and

Battery ↔ Bidirectional DC–DC Converter ↔ DC Bus

Main System Ratings

Parameter

Value / Description

PV module power

250 W

Number of PV modules

8

PV configuration

8 modules in series

Total PV rated power

Approximately 2000 W

Standard irradiance

1000 W/m²

Standard temperature

25°C

Battery configuration

20 × 12 V batteries in series

Battery nominal voltage

Approximately 240 V

Battery capacity

48 Ah

DC bus reference voltage

400 V

DC load power

Approximately 1000 W

PV converter

Boost converter

Battery converter

Bidirectional DC–DC converter

MPPT method

Fuzzy Logic MPPT

Battery-side control

DC bus voltage control

𝐒𝐨𝐥𝐚𝐫 𝐏𝐕 𝐀𝐫𝐫𝐚𝐲

The PV array consists of eight 250 W solar modules connected in series, giving a maximum rated output of approximately:

2000 W under standard test conditions.

Solar PV output is highly dependent on:

  • Solar irradiation

  • Temperature

  • Operating voltage

  • Operating current

Because the PV characteristic is nonlinear, the maximum-power operating point changes whenever the environmental conditions change.

For this reason, the PV array cannot simply be connected to the DC bus and expected to deliver maximum power continuously.

A suitable MPPT controller is required.

𝐖𝐡𝐲 𝐅𝐮𝐳𝐳𝐲 𝐌𝐏𝐏𝐓 𝐢𝐬 𝐔𝐬𝐞𝐝

The Fuzzy MPPT controller continuously observes the PV operating condition and adjusts the boost converter duty cycle.

The main advantages of this approach include:

  • Fast response to changing irradiation

  • Good maximum power tracking capability

  • No requirement for an exact mathematical PV model

  • Suitable operation under nonlinear PV characteristics

  • Flexible rule-based control

  • Reduced dependence on fixed-step perturbation

The controller uses PV voltage and current measurements to determine the appropriate operating direction.

𝐅𝐮𝐳𝐳𝐲 𝐌𝐏𝐏𝐓 𝐈𝐧𝐩𝐮𝐭𝐬

The Fuzzy Logic controller uses information derived from the PV voltage and power.

Two important quantities are considered:

  • PV operating slope

  • Change in the slope

These parameters indicate the position of the PV operating point relative to the maximum power point.

The controller then determines how the converter duty cycle should be adjusted.

Fuzzy Controller Details

Item

Description

Measured PV quantities

Voltage and current

Calculated quantity

PV power

Main fuzzy input

PV power-voltage slope

Second fuzzy input

Change in slope

Controller output

Duty cycle adjustment

Fuzzy rule base

49 rules

Converter controlled

PV boost converter

Switching control

PWM

The model uses a pre-designed 49-rule fuzzy rule base containing input and output membership functions.

𝐖𝐨𝐫𝐤𝐢𝐧𝐠 𝐏𝐫𝐨𝐜𝐞𝐬𝐬

The operation of the complete system can be divided into several stages.

1. PV Voltage and Current Measurement

The PV array voltage and current are continuously measured.

These signals are used to determine the instantaneous PV power and operating condition.

2. Fuzzy MPPT Processing

The Fuzzy MPPT controller evaluates:

  • Present PV condition

  • Previous sampled condition

  • Variation in PV voltage

  • Variation in PV power

  • PV operating slope

  • Change in operating slope

Based on these quantities, the fuzzy controller determines the required converter duty cycle.

3. PWM Generation

The duty-cycle output is passed to the PWM generator.

The PWM signal controls the switching device of the PV boost converter.

4. PV Maximum Power Extraction

By continuously modifying the duty cycle, the boost converter changes the operating point of the PV array.

The controller therefore attempts to keep the PV system near its maximum power point even when irradiation changes.

5. Energy Transfer to DC Bus

The extracted PV power is transferred to the common DC bus.

The DC bus supplies the connected DC load and interacts with the battery storage system.

𝐁𝐨𝐨𝐬𝐭 𝐂𝐨𝐧𝐯𝐞𝐫𝐭𝐞𝐫

The PV array is connected to the DC bus through a DC–DC boost converter.

Its main functions are:

  • Interface the PV array with the higher-voltage DC bus

  • Control PV operating voltage

  • Enable MPPT operation

  • Transfer available PV energy to the DC bus

  • Respond to the duty-cycle command generated by the fuzzy controller

The switching operation of this converter is directly linked to the output of the Fuzzy MPPT controller.

𝐁𝐚𝐭𝐭𝐞𝐫𝐲 𝐄𝐧𝐞𝐫𝐠𝐲 𝐒𝐭𝐨𝐫𝐚𝐠𝐞

The battery system consists of approximately 20 batteries of 12 V connected in series.

This gives a nominal battery-bank voltage of approximately 240 V.

The stated battery capacity is 48 Ah.

The battery provides an important balancing function in the DC microgrid.

It can operate in:

  • Charging mode

  • Discharging mode

  • Near-idle condition

Its operating mode depends primarily on the available PV power and load demand.

𝐁𝐢𝐝𝐢𝐫𝐞𝐜𝐭𝐢𝐨𝐧𝐚𝐥 𝐃𝐂–𝐃𝐂 𝐂𝐨𝐧𝐯𝐞𝐫𝐭𝐞𝐫

The battery is connected to the common DC bus through a bidirectional DC–DC converter.

Unlike a conventional unidirectional converter, this converter permits power transfer:

  • From the DC bus to the battery during charging

  • From the battery to the DC bus during discharging

This makes the battery capable of supporting the DC load while also absorbing surplus PV power.

𝐂𝐨𝐧𝐭𝐫𝐨𝐥 𝐒𝐭𝐫𝐚𝐭𝐞𝐠𝐲

The control strategy has two major sections.

PV-Side Control

The PV-side boost converter is controlled by the Fuzzy MPPT algorithm.

Its purpose is to:

  • Track changing PV conditions

  • Adjust converter duty cycle

  • Extract maximum available solar power

Battery-Side Control

The bidirectional converter is controlled primarily to maintain the DC bus voltage around:

400 V

The actual DC bus voltage is measured and compared with the reference value.

The resulting control signal is processed through a controller and PWM generator to control the battery converter switches.

This allows the battery to react automatically to changes in generation and load.

𝐏𝐨𝐰𝐞𝐫 𝐁𝐚𝐥𝐚𝐧𝐜𝐢𝐧𝐠 𝐌𝐨𝐝𝐞𝐬

The operating condition of the battery depends on the relationship between PV power and load power.

PV Power Condition

Battery Mode

System Behaviour

PV power > Load power

Charging

Excess PV power charges the battery

PV power ≈ Load power

Near idle

PV approximately supplies the complete load

PV power < Load power

Discharging

Battery supplies the missing load power

This power-balancing process enables stable operation of the DC microgrid.

𝐃𝐂 𝐁𝐮𝐬 𝐕𝐨𝐥𝐭𝐚𝐠𝐞 𝐂𝐨𝐧𝐭𝐫𝐨𝐥

One of the most important requirements in a DC microgrid is maintaining a stable common bus voltage.

In this system, the target DC bus voltage is:

400 V

The battery-side converter compensates for the difference between solar generation and load consumption.

For example:

  • When PV generation increases, the battery absorbs excess energy.

  • When PV generation decreases, the battery supplies additional power.

  • As a result, large DC bus voltage variations are minimized.

This control approach helps create a stable electrical supply for the connected DC load.

𝐈𝐫𝐫𝐚𝐝𝐢𝐚𝐧𝐜𝐞 𝐕𝐚𝐫𝐢𝐚𝐭𝐢𝐨𝐧 𝐓𝐞𝐬𝐭

The model is tested under rapidly changing solar irradiation.

The irradiation is changed approximately every 0.3 seconds.

The test includes decreasing irradiation followed by increasing irradiation.

Irradiance Test Conditions

Test Stage

Irradiance

Initial condition

1000 W/m²

Reduced condition

800 W/m²

Reduced condition

500 W/m²

Low condition

300 W/m²

Very low condition

Approximately 10 W/m²

Recovery condition

300 W/m²

Recovery condition

500 W/m²

Recovery condition

800 W/m²

Final condition

1000 W/m²

This changing profile is useful for evaluating both the MPPT response and battery power-balancing performance.

𝐒𝐢𝐦𝐮𝐥𝐚𝐭𝐢𝐨𝐧 𝐑𝐞𝐬𝐮𝐥𝐭𝐬

The simulation monitors several important system quantities.

PV Measurements

The model displays:

  • PV voltage

  • PV current

  • PV power

As irradiation decreases, the available PV power also decreases.

When irradiation increases again, the PV output rises accordingly.

The Fuzzy MPPT controller adjusts the converter operation to follow these changing maximum-power conditions.

𝐏𝐕 𝐏𝐨𝐰𝐞𝐫 𝐔𝐧𝐝𝐞𝐫 𝐃𝐢𝐟𝐟𝐞𝐫𝐞𝐧𝐭 𝐈𝐫𝐫𝐚𝐝𝐢𝐚𝐧𝐜𝐞

The transcript indicates the following approximate operating values.

Irradiance

Approximate PV Power

Battery Behaviour

1000 W/m²

2000 W

Charging

800 W/m²

1600 W

Charging

500 W/m²

Around 1000 W

Near balance / slight battery support

Below 500 W/m²

Below load demand

Discharging

Irradiance increasing again

PV power increases

Returns toward charging

These results demonstrate the energy-balancing action of the battery.

𝐁𝐚𝐭𝐭𝐞𝐫𝐲 𝐑𝐞𝐬𝐩𝐨𝐧𝐬𝐞

At high irradiation:

  • PV power is greater than the DC load demand.

  • Excess solar energy is transferred to the battery.

  • Battery current indicates charging.

  • Battery SOC gradually increases.

At lower irradiation:

  • PV power becomes insufficient for the load.

  • The bidirectional converter reverses the power flow.

  • The battery supplies the missing energy.

  • Battery SOC gradually decreases.

Once solar generation increases again, the battery returns to charging operation.

𝐂𝐮𝐫𝐫𝐞𝐧𝐭 𝐃𝐢𝐫𝐞𝐜𝐭𝐢𝐨𝐧

In the displayed simulation results, battery current polarity can be used to identify the operating mode.

Battery Current

Operating Interpretation

Negative current

Battery charging

Positive current

Battery discharging

Current close to zero

Battery nearly idle

For example, under higher solar generation, the battery current becomes negative because the excess PV energy is being stored.

𝐃𝐂 𝐋𝐨𝐚𝐝 𝐑𝐞𝐬𝐮𝐥𝐭𝐬

The DC load is approximately:

1000 W

The simulation observes:

  • DC bus voltage

  • DC load current

  • DC load power

Even when PV power changes significantly due to irradiation variation, the battery-side voltage controller helps maintain the common DC bus close to 400 V.

This indicates effective coordination between renewable generation, battery storage, and load demand.

𝐒𝐎𝐂 𝐑𝐞𝐬𝐩𝐨𝐧𝐬𝐞

Battery state of charge follows the charging and discharging process.

The observed behaviour is:

  • SOC increases when excess PV energy is available.

  • SOC decreases when the battery supports the load.

  • SOC again increases when irradiation and PV power recover.

The SOC response therefore confirms that the bidirectional converter is correctly controlling battery energy flow.

𝐎𝐩𝐞𝐫𝐚𝐭𝐢𝐧𝐠 𝐂𝐨𝐧𝐝𝐢𝐭𝐢𝐨𝐧 𝐒𝐮𝐦𝐦𝐚𝐫𝐲

Condition

PV Generation

Load Demand

Battery

Strong sunlight

High

Constant

Charges

Moderate sunlight

Medium

Constant

Charging reduces

PV approximately equals load

Balanced

Constant

Nearly idle

Weak sunlight

Low

Constant

Discharges

Solar power recovers

Increasing

Constant

Returns to charging

𝐊𝐞𝐲 𝐅𝐞𝐚𝐭𝐮𝐫𝐞𝐬

  • 2 kW solar PV system

  • Fuzzy Logic based MPPT

  • 49-rule fuzzy controller

  • PV voltage and current feedback

  • Dynamic duty-cycle generation

  • PWM controlled boost converter

  • Battery energy storage

  • Bidirectional DC–DC converter

  • Automatic charging and discharging

  • 400 V DC bus regulation

  • Variable irradiation simulation

  • PV voltage, current, and power monitoring

  • Battery voltage, current, and SOC monitoring

  • DC load voltage, current, and power monitoring

  • Power-balancing demonstration

  • MATLAB/Simulink implementation

𝐁𝐞𝐧𝐞𝐟𝐢𝐭𝐬 𝐨𝐟 𝐭𝐡𝐞 𝐏𝐫𝐨𝐩𝐨𝐬𝐞𝐝 𝐂𝐨𝐧𝐭𝐫𝐨𝐥

Efficient PV Utilization

The Fuzzy MPPT controller attempts to keep the solar array operating close to its maximum power point.

Stable DC Bus

The battery-side converter helps regulate the DC bus around the selected 400 V reference.

Automatic Power Sharing

The battery reacts automatically to the difference between PV generation and load demand.

Renewable Energy Support

Energy available during strong sunlight can be stored instead of being wasted.

Load Support

During weak solar conditions, stored battery energy can maintain power delivery to the DC load.

Dynamic Performance Testing

The irradiation profile allows the system behaviour to be studied under changing environmental conditions rather than only at one fixed operating point.

𝐀𝐩𝐩𝐥𝐢𝐜𝐚𝐭𝐢𝐨𝐧𝐬

This MATLAB/Simulink model is useful for studying:

  • Solar PV DC microgrids

  • Renewable energy control

  • Fuzzy Logic MPPT

  • Battery-integrated PV systems

  • DC bus voltage regulation

  • Bidirectional converter control

  • Energy storage systems

  • Standalone DC networks

  • Smart DC distribution systems

  • Renewable energy laboratories

  • MPPT algorithm analysis

  • Power electronic converter studies

  • Battery charging and discharging control

  • Energy-management research

𝐖𝐡𝐚𝐭 𝐂𝐚𝐧 𝐁𝐞 𝐀𝐧𝐚𝐥𝐲𝐳𝐞𝐝 𝐟𝐫𝐨𝐦 𝐭𝐡𝐞 𝐌𝐨𝐝𝐞𝐥?

Students, researchers, and engineers can use the model to analyze:

  • Effect of irradiation variation on PV power

  • Fuzzy MPPT tracking behaviour

  • PV operating voltage variation

  • PV current variation

  • PV power response

  • Boost converter switching performance

  • Battery charging behaviour

  • Battery discharging behaviour

  • Battery current direction

  • Battery SOC variation

  • DC bus voltage stability

  • DC load power

  • Power-sharing between PV and battery

  • Response of the system during sudden solar power reduction

  • Recovery when solar irradiation increases

𝐒𝐢𝐦𝐮𝐥𝐚𝐭𝐢𝐨𝐧 𝐒𝐢𝐠𝐧𝐚𝐥𝐬 𝐀𝐯𝐚𝐢𝐥𝐚𝐛𝐥𝐞

System Section

Signals Observed

Solar PV

Voltage, current, power

Battery

Voltage, current, SOC

DC bus

DC bus voltage

DC load

Voltage, current, power

MPPT controller

Duty-cycle response

Converter

PWM switching command

Operating environment

Irradiance variation

𝐖𝐡𝐲 𝐭𝐡𝐢𝐬 𝐌𝐨𝐝𝐞𝐥 𝐢𝐬 𝐔𝐬𝐞𝐟𝐮𝐥

This model provides a clear demonstration of how different control sections interact inside a renewable DC microgrid.

Instead of studying MPPT, battery control, and DC bus regulation separately, the model combines them in one integrated simulation.

It helps users understand:

  • How maximum solar power is extracted

  • How the battery compensates for changing PV generation

  • How excess renewable energy is stored

  • How the battery supports the load during low irradiation

  • How a stable DC bus is maintained

  • How Fuzzy Logic can be applied to nonlinear renewable-energy control

𝐂𝐨𝐧𝐜𝐥𝐮𝐬𝐢𝐨𝐧

The Fuzzy MPPT For Solar PV Battery DC Microgrid System in MATLAB demonstrates an integrated renewable-energy system combining a 2 kW solar PV array, Fuzzy MPPT controller, boost converter, battery storage, bidirectional DC–DC converter, and DC load.

The Fuzzy MPPT algorithm controls the PV boost converter to extract maximum available solar power under changing irradiation conditions. At the same time, the battery-side bidirectional converter regulates the common DC bus around 400 V.

When PV generation exceeds the approximately 1 kW load demand, the excess energy charges the battery. When PV generation becomes insufficient, the battery discharges and supplies the required additional power.

The simulation therefore provides a useful platform for understanding maximum power point tracking, battery energy management, bidirectional power flow, DC bus regulation, and renewable-energy power balancing within a solar PV battery DC microgrid.

Comments


bottom of page