top of page

Speed control of BLDC motor using H Infinity Controller in MATLAB

1 day ago
7 min read

Speed control of BLDC motor using H Infinity Controller in MATLAB


𝐈𝐧𝐭𝐫𝐨𝐝𝐮𝐜𝐭𝐢𝐨𝐧

The Speed Control of BLDC Motor Using H Infinity Controller in MATLAB demonstrates an advanced control technique for achieving accurate and smooth speed regulation of a Brushless DC (BLDC) motor.



Speed control of BLDC motor using H Infinity Controller in MATLAB
₹8,000.00₹4,000.00
Buy Now


BLDC motors are widely used in electric vehicles, robotics, industrial automation, and high-performance motor drive systems because of their high efficiency, reliability, and low maintenance requirements.

The 𝐇-𝐈𝐧𝐟𝐢𝐧𝐢𝐭𝐲 (𝐇∞) 𝐂𝐨𝐧𝐭𝐫𝐨𝐥𝐥𝐞𝐫 is a robust control technique designed to maintain satisfactory system performance in the presence of modeled disturbances and uncertainties.

This MATLAB/Simulink implementation focuses on:

  • BLDC motor speed regulation using H∞ control.

  • Transfer function identification using input-output data.

  • H∞ controller design and synthesis.

  • Hall sensor-based inverter switching.

  • Reference speed tracking under changing operating conditions.

  • Analysis of motor speed, torque, current, back EMF, and voltage.

𝐒𝐲𝐬𝐭𝐞𝐦 𝐎𝐯𝐞𝐫𝐯𝐢𝐞𝐰

The proposed system consists of a controlled DC voltage source, three-phase voltage source inverter, BLDC motor, Hall sensor-based commutation system, and H∞ speed controller.

Main Components

Component

Function

BLDC Motor

Converts electrical energy into mechanical rotation

Controlled Voltage Source

Regulates the DC input voltage

Three-Phase Inverter

Supplies the required phase voltages to the motor

Hall Sensor Decoder

Identifies rotor position for electronic commutation

Gate Pulse Generator

Produces inverter switching signals

H∞ Controller

Regulates motor speed through feedback control

Speed Measurement

Provides actual rotor speed for feedback

Measurement Blocks

Monitor motor current, back EMF, torque, and voltage

The H∞ controller continuously compares the reference speed with the actual motor speed and adjusts the controlled voltage source to reduce the speed error.

𝐒𝐲𝐬𝐭𝐞𝐦 𝐒𝐩𝐞𝐜𝐢𝐟𝐢𝐜𝐚𝐭𝐢𝐨𝐧𝐬

The following parameters are used in the demonstrated MATLAB/Simulink implementation.

Parameter

Value

Motor Type

Brushless DC Motor

Simulation Software

MATLAB/Simulink

Speed Controller

H Infinity (H∞)

Initial Reference Speed

3000 RPM

Final Reference Speed

2000 RPM

Speed Change Time

1 second

Total Simulation Time

2 seconds

Initial DC Bus Voltage

Approximately 480 V

DC Bus Voltage After Speed Change

Approximately 330 V

Initial Speed Settling Time

Approximately 0.4 seconds

Speed Settling After Reference Change

Approximately 1.3 seconds (absolute simulation time)

Inverter

Three-Phase Voltage Source Inverter

Commutation Method

Hall Sensor-Based Electronic Commutation

Values are based on the demonstrated simulation. The DC bus voltages and settling times are approximate observations rather than specified controller guarantees.

𝐖𝐨𝐫𝐤𝐢𝐧𝐠 𝐏𝐫𝐨𝐜𝐞𝐬𝐬

The BLDC motor speed control system operates through a closed-loop control structure.

Reference Speed (RPM)

Speed Error Calculation

Reference Speed − Actual Speed

H∞ Speed Controller

Controlled DC Voltage Source

Three-Phase Inverter and Hall Sensor Commutation

BLDC Motor

 

Actual speed is measured and fed back to the controller

Step-by-Step Operation

  1. Reference Speed: The required motor speed is set to 3000 RPM initially.

  2. Speed Comparison: Actual rotor speed is measured and compared with the reference.

  3. H∞ Control: The controller processes the speed error and generates a voltage control command.

  4. Voltage Regulation: The controlled voltage source adjusts the DC voltage supplied to the inverter.

  5. Electronic Commutation: Hall sensor signals determine the appropriate inverter switching sequence.

  6. Motor Operation: The BLDC motor responds to the applied voltage and inverter commutation.

  7. Feedback Regulation: The controller continuously adjusts the voltage to track the reference speed.

𝐓𝐫𝐚𝐧𝐬𝐟𝐞𝐫 𝐅𝐮𝐧𝐜𝐭𝐢𝐨𝐧 𝐈𝐝𝐞𝐧𝐭𝐢𝐟𝐢𝐜𝐚𝐭𝐢𝐨𝐧

Before designing the H∞ controller, the dynamic behavior of the BLDC motor must be identified.

MATLAB provides the System Identification tools to estimate a transfer function using measured or simulated input-output data.

Data Collection

The motor model is simulated by applying a varying input voltage to the controlled voltage source and recording the corresponding motor speed.

Parameter

Value

Input Variable

Controlled DC Voltage

Output Variable

Rotor Speed

Initial Identification Voltage

300 V

Final Identification Voltage

500 V

Input Voltage Change Time

1 second

Data Collection Duration

2 seconds

Number of Samples

40,000

Sampling Time

5 × 10⁻⁵ seconds

Input Data Variable

in

Output Data Variable

out

Identification Procedure

  • Open the MATLAB System Identification app using ident.

  • Import the motor input and output data from the MATLAB workspace.

  • Select time-domain data.

  • Specify the sampling time.

  • Apply mean removal when appropriate.

  • Select transfer function estimation.

  • Specify the required poles and zeros.

  • Estimate the motor transfer function.

  • Compare the estimated model response with the collected output.

Transfer Function Estimation

Parameter

Selected Value

Number of Poles

2

Number of Zeros

1

Initial Estimation

Discrete-Time Model

Final Estimation

Continuous-Time Model

Reported Model Fit

Approximately 93.19%

The estimated transfer function represents the input-voltage-to-motor-speed relationship for the operating conditions used during identification.

The reported 93.19% model fit indicates agreement between the identified model and the identification dataset. Separate validation is necessary to establish its accuracy under different operating conditions.

𝐇-𝐈𝐧𝐟𝐢𝐧𝐢𝐭𝐲 𝐂𝐨𝐧𝐭𝐫𝐨𝐥 𝐒𝐭𝐫𝐚𝐭𝐞𝐠𝐲

The H∞ controller is designed to improve the speed regulation performance of the BLDC motor.

Unlike a conventional controller tuned mainly for nominal operation, H∞ control provides a mathematical framework for addressing disturbance sensitivity and robustness.

Controller Design Procedure

  • Obtain the BLDC motor transfer function from system identification.

  • Represent the motor dynamics in MATLAB.

  • Define suitable disturbance and performance weighting models.

  • Construct a generalized plant.

  • Perform H∞ controller synthesis.

  • Obtain the controller in state-space representation.

  • Convert the controller into a transfer function representation when appropriate.

  • Implement the controller using the MATLAB/Simulink Transfer Function block.

  • Test the closed-loop motor response for different reference speed commands.

Role of the H∞ Controller

Control Objective

Description

Speed Tracking

Follow the required motor speed

Disturbance Attenuation

Reduce the influence of modeled disturbances

Overshoot Reduction

Limit excessive speed excursions

Settling Performance

Achieve the commanded speed with suitable transient behavior

Robustness

Maintain performance over modeled plant variations

Closed-Loop Stability

Support stable motor operation through suitable controller synthesis and validation

The quality of H∞ control depends on the accuracy of the identified plant model and the selection of performance weighting functions.

𝐌𝐀𝐓𝐋𝐀𝐁/𝐒𝐈𝐌𝐔𝐋𝐈𝐍𝐊 𝐈𝐌𝐏𝐋𝐄𝐌𝐄𝐍𝐓𝐀𝐓𝐈𝐎𝐍

The developed H∞ controller is connected to the BLDC motor simulation through the controlled voltage source.

Implementation Steps

  1. Create the BLDC motor and inverter model in Simulink.

  2. Configure Hall sensor-based gate pulse generation.

  3. Measure the actual rotor speed.

  4. Convert motor speed from rad/s to RPM.

  5. Compare actual speed with reference speed.

  6. Connect the speed error to the H∞ controller block.

  7. Apply the controller output to the controlled voltage source.

  8. Observe speed, voltage, electromagnetic torque, current, and back EMF.

The design uses a closed-loop feedback mechanism to regulate the motor speed automatically.

𝐒𝐢𝐦𝐮𝐥𝐚𝐭𝐢𝐨𝐧 𝐑𝐞𝐬𝐮𝐥𝐭𝐬

The MATLAB/Simulink results demonstrate the response of the BLDC motor when the reference speed changes from 3000 RPM to 2000 RPM.

1. Rotor Speed Response

BLDC Motor Speed Tracking

Illustrative response based on approximate settling times described in the simulation narration; not raw simulation samples.

■ Reference speed

■ Illustrative actual speed

Illustrative visualization of the described speed response, not an exact reconstruction of exported MATLAB data.

The demonstrated simulation indicates that:

  • Motor speed increases smoothly from standstill to 3000 RPM.

  • The initial speed settles at approximately 0.4 seconds.

  • At 1 second, the reference speed changes to 2000 RPM.

  • The motor reaches the new reference at approximately 1.3 seconds.

  • No significant overshoot is visible in the demonstrated speed response.

2. DC Bus Voltage Response

The DC bus voltage varies according to the motor speed requirement.

Operating Condition

Approximate DC Voltage

3000 RPM Operation

480 V

2000 RPM Operation

330 V

The controller reduces the commanded DC voltage when the required motor speed decreases.

3. Electromagnetic Torque Response

The electromagnetic torque changes during motor acceleration and speed transitions.

Observed behavior:

  • Initially, the motor develops torque to accelerate the rotor.

  • Torque approaches a steady operating value after the motor reaches its reference speed.

  • A transient occurs when the reference speed changes.

  • Torque settles as the motor reaches its new operating condition.

4. Stator Current and Back EMF

The stator current and back EMF waveforms illustrate the electrical behavior of the BLDC motor.

  • Stator current varies during acceleration and speed transitions.

  • Back EMF magnitude increases with motor speed.

  • When speed decreases, the back EMF magnitude also decreases.

  • Hall sensor-based commutation maintains the required phase switching sequence.

5. Line-to-Line Voltage

The inverter output voltage responds to changes in the controlled DC input.

  • Higher speed operation corresponds to a higher voltage envelope in the demonstrated system.

  • The voltage envelope decreases after the speed reference is reduced.

  • The inverter continues supplying electronically commutated phase voltages.

Overall Performance Summary

Performance Parameter

Observed Result

Initial Speed Reference

3000 RPM

Final Speed Reference

2000 RPM

Initial Settling Time

Approximately 0.4 s

Settling Time After Step Change

Approximately 0.3 s after the 1 s command

Speed Tracking

Successful in demonstrated test

Overshoot

No significant overshoot visible

DC Voltage Regulation

Responds to speed reference

Torque Response

Transient during speed change

Back EMF

Varies with rotor speed

Motor Operation

Stable in the demonstrated simulation

These results demonstrate satisfactory reference-speed tracking for the simulated operating conditions. Additional load-disturbance and parameter-uncertainty tests would be required to quantify the controller's robustness.

𝐊𝐞𝐲 𝐅𝐞𝐚𝐭𝐮𝐫𝐞𝐬

  • 𝐑𝐨𝐛𝐮𝐬𝐭 𝐇∞ 𝐂𝐨𝐧𝐭𝐫𝐨𝐥: Advanced feedback control for BLDC motor speed regulation.

  • 𝐒𝐲𝐬𝐭𝐞𝐦 𝐈𝐝𝐞𝐧𝐭𝐢𝐟𝐢𝐜𝐚𝐭𝐢𝐨𝐧: MATLAB-based transfer function estimation from input-output data.

  • 𝐒𝐩𝐞𝐞𝐝 𝐓𝐫𝐚𝐜𝐤𝐢𝐧𝐠: Automatic adjustment to changing reference speed commands.

  • 𝐒𝐦𝐨𝐨𝐭𝐡 𝐑𝐞𝐬𝐩𝐨𝐧𝐬𝐞: Low-overshoot speed tracking demonstrated in simulation.

  • 𝐇𝐚𝐥𝐥 𝐒𝐞𝐧𝐬𝐨𝐫 𝐂𝐨𝐦𝐦𝐮𝐭𝐚𝐭𝐢𝐨𝐧: Rotor position-based inverter gate pulse generation.

  • 𝐃𝐂 𝐕𝐨𝐥𝐭𝐚𝐠𝐞 𝐂𝐨𝐧𝐭𝐫𝐨𝐥: Input voltage regulation through the H∞ speed control loop.

  • 𝐂𝐨𝐦𝐩𝐥𝐞𝐭𝐞 𝐌𝐨𝐭𝐨𝐫 𝐌𝐨𝐧𝐢𝐭𝐨𝐫𝐢𝐧𝐠: Observation of speed, electromagnetic torque, stator current, back EMF, and line voltage.

𝐀𝐩𝐩𝐥𝐢𝐜𝐚𝐭𝐢𝐨𝐧𝐬

BLDC motor speed control using H∞ techniques can be investigated for several applications.

Application

Relevance

Electric Vehicles

Traction motor speed regulation

Industrial Automation

Controlled-speed motor drives

Robotics

Accurate actuator and motor speed control

Electric Pumps

Adjustable-speed pump operation

Cooling Fans

Speed regulation under varying demands

Electric Compressors

Motor drive performance control

Aerospace Systems

Robust motor drive control studies

Research and Education

System identification and robust controller design

𝐖𝐡𝐲 𝐔𝐬𝐞 𝐇∞ 𝐂𝐨𝐧𝐭𝐫𝐨𝐥 𝐟𝐨𝐫 𝐁𝐋𝐃𝐂 𝐌𝐨𝐭𝐨𝐫𝐬?

H∞ control is particularly useful when motor performance must be evaluated under uncertainties and disturbances.

Its main advantages include:

  • A systematic framework for robust controller synthesis.

  • Ability to incorporate disturbance attenuation objectives.

  • Flexibility in defining desired speed-tracking performance.

  • Suitability for multi-objective feedback control design.

  • Compatibility with MATLAB-based control analysis and simulation.

However, H∞ controller design generally requires a suitable dynamic model and carefully selected weighting functions. Its superiority over PI, PID, or other control techniques must be established through comparative testing rather than assumed.

𝐂𝐨𝐧𝐜𝐥𝐮𝐬𝐢𝐨𝐧

The Speed Control of BLDC Motor Using H Infinity Controller in MATLAB demonstrates an effective approach to closed-loop motor speed regulation using system identification and robust control synthesis.

The identified BLDC motor model is used to design an H∞ controller, which regulates the controlled DC voltage based on the difference between reference and actual motor speed.

In the demonstrated simulation, the motor successfully tracks a speed change from 3000 RPM to 2000 RPM with smooth transient behavior and no significant visible overshoot.

This implementation provides a useful foundation for students, researchers, and engineers studying BLDC motor drives, MATLAB/Simulink modeling, system identification, and advanced feedback control techniques.

Explore more MATLAB/Simulink tutorials and motor control simulations at LMS Solution.


Comments


bottom of page